Speaker cabs materials

Speaker cabinets and head cabinets can be made of variety of materials. Many players never really think about what their cab is made of since most are covered in tolex and the  materials are not obvious. Despite this the materials used are important for two reasons: they affect the durability of the cab and they affect the tone of cabs.  The cost of the cab often depends on the materials used. With a little knowledge a you can make informed decisions about cabs.   In this article we will look at the materials used.  Generally cabs are made of one of four materials: particle board, Medium Density Fiberboard or MDF, hardwood plywood, or solid woods.

Particle Board:

What is it?
Particle board is made of sawdust and wood chips that held together by glue.  It’s an inexpensive material and easy to machine.  It very dense and heavy and cabs made with it weigh in on the heavy side.

What Cabs Have It?
Particle board can be used for all or part of a cab’s material.  Particle board cabs are usually found in low quality and low cost amps. You might also see it as baffle material or panel material in certain amps.
How Does it Sound?
Particle board is sonically dead and tends to absorb sound. Hi-Fi people like it because it does not alter the sound so you just hear the speaker but guitar players find it to be less lively than other materials.
How does it hold up?
This where particle board really fails. It simply does not hold up well to long term use.  Particle board cabs need additional bracing to be sturdy and over time they absorb moisture and fall apart. If you live in dry area or do not travel with cab it will last much longer.  Many later Silverface Fenders use particle board for baffles and front panels of heads. I dread having to remove speakers from particle board baffles because they often crumble.

MDF

What is it?
MDF is made of wood fiber pressed in large boards. It got less voids than particle board and is made of smaller fibers.   It’s tougher than particle board and is  heavy so cabs made with it are heavy too.  It’s more durable than particle board and easy to work with.
What Cabs Have It?
Many cabs are made with MDF.  Its one of the most common materials for lower end bass cabs and pa speaker cabs. It can be used in whole cab or as panels for cabs.
How Does it Sound?
MDF is sonically dead and tends to absorb sound. Hi-Fi people and bass players people like it because  it does not alter the sound of the speaker but guitar players find it to be less lively than other materials in cab meant to be resonant. In non resonant cabs it’s a fine material.
How does it hold up?
While tougher than particle boards they can  absorb moisture and fall apart but it’s much less of an issue than with particle board. It critical to keep them dry .  MDF holds together well so long as the cab has adequate bracing.

Hardwood Plywood

What is it?
Plywood sheets are made from layers of thin wood pieces with each ply or layer laid down at a 90 degree angle gain wise.  These are glued together. Plywood can be made of lots of materials but for this discussion we will limit ourselfs to hardwood since pine and softwood plywoods is not appropaite for cab construction. Birch plywood is the most common in cabs.
What Cabs Have It?
The majority of upper end cab makers use plywoods.  Marshall 1960 cabs, Hiwatt Cabs, Mesa Cab etc etc are all made of plywoods. They are industry standard for good cabs!

How Does it Sound?
Plywoods resonate more that MDF or Particle Board and tend to sound more lively and punchy to the ear.

How does it hold up?
Plywoods are tougher than MDF and do not have as much of a problem with mosture absortion.  They will hold up well on the road assuming the cab is properly constructed. Plywood tends to be very stable and not warp over time so long as it is not been exposed to too much mosture.

Solid Woods

What is it?
Solid wood cabs are made of real wood! This is not to say they are all made of single piece. Often solid wood is more stable and less prone to warp when a few pieces are edge joined to form a panel.  Pine is the most common material but other species can be used.
What Cabs Have It?
Some high end amps have it. Vintage Fender and other American made amps often used solid pine.

How Does it Sound?
Solid wood tend to be more lively and resonate than any of the other materials. It adds to the tone of the speaker with pleasing overtones.  The species of wood and it’s density affect how it resonates so it varies from cab to cab and one piece of wood to another. Much like a guitar.

How does it hold up?
Solid wood cabs when built well are as tough as the come when built correctly.
Recommendation:
Solid wood cabs are really worth trying out.  They sound great and hold up really well. VL Effects uses it for all it’s Amps and Cabs and for others as well.